Skip to main content

what are the Major Infrastructure Construction Projects in Africa 2021

 The following are some major infrastructure projects in Africa that are ongoing, or in planning and under development, in 2021.

1. Grand Inga Dam: Congo

The Grand Inga Dam is the world's largest proposed hydropower project, and it is being built on the Congo River in the Democratic Republic of the Congo. It is the cornerstone of the country’s grand vision to assist in the development of a continent-wide power system.

The project is expected to generate 40,000 MW of power. This is enough to power nearly half of the continent and is nearly twice as large as China's Three Gorges Dam. It is estimated that approximately US$80 billion will be required to complete the project. This will entail the installation of transmission lines across the continent.

2. Dangote Oil Refinery: Nigeria

The Dangote Oil Refinery project is on track to become the world's largest single oil refinery. The facility, which will be located in Nigeria, will have a capacity of 650,000 barrels per day, boosting economic growth and creating thousands of jobs.

The refinery project will cost a whopping US$14 billion , and when finished, the planned refinery and petrochemical complex will account for half of Africa's richest man, Aliko Dangote's vast assets. It is also expected to increase the country's oil exports and decrease its reliance on petroleum product imports. In September 2020, ConstructAfrica reported that majority of the heavy refinery components for the project had been delivered to site by heavy lifting and transport contractor, Mammoet. 

3. Bagamoyo Port: Tanzania

Tanzania's Bagamoyo port is set to become the largest in East and Central Africa. Tanzania, China, and Oman are collaborating on the project. The port is being built by the state-owned China Merchants Port, and an Omani sovereign wealth fund will establish a 1,700-hectare special economic zone adjacent to it.

The port project, which is expected to cost US$10 billion, is expected to take about 30 years to complete to reach its full potential. The port will be able to handle twenty times more cargo than the country's largest port, which is located in the Tanzanian capital of Dar es Salaam.

4. New Capital City: Egypt

Egypt's gleaming new capital, rising from the desert sands, is set to bring a breath of fresh air to Cairo, which is burdened by an ever-increasing population that puts a strain on existing infrastructure.

The smart city is 45 kilometers east of Cairo and has 21 residential districts and 25 commercial districts. The city will have a recreation park twice the size of New York City's Central Park, solar energy farms covering 90 square kilometers, and several artificial lakes. In its first phase, the new capital is expected to attract a population of 7 million people.

5. Konza Technology City: Kenya

Konza Technology City is a smart city project that will be built in the country's east. The project, which is part of the country's Vision 2030 blueprint, is expected to create approximately 17,000 direct high-value jobs and an additional 68,000 indirect jobs once completed.

The project, which is 64 kilometers south of Nairobi, is modeled after Silicon Valley in the United States, hence the name "African Silicon Savanna." It is primarily aimed at business process outsourcing, software development, data centers, disaster recovery centers, call centers, light manufacturing industries, and research institutions. The total cost of the project is US$14.5 billion.

6. Standard Gauge Railway: Kenya

Kenya is spending US$9.9 billion to build a 969-kilometer standard gauge railway from Mombasa to Malaba. This has been billed as one of Africa's largest and most ambitious transportation infrastructure projects.

The first phase of the project, which spans 472 kilometers from Mombasa to Nairobi, was completed at a cost of US$3.27 billion, while phase 2A, which spans 120 kilometers from Nairobi to Naivasha, was completed at a cost of US$1.5 billion. The railway line is expected to be extended to Kisumu for a cost of US$3.7 billion.

7. New Railway: Lagos-Calabar

The 1,400-kilometer Lagos-Calabar railway, which will cost US$10 billion, is without a doubt one of Africa's major infrastructure projects.

The project, which was originally contracted to a Chinese company, is now being pursued by Ameri Metro Inc., based in the United States, after the Chinese were unable to raise the necessary funds.

When completed, the Lagos-Calabar railway will link the cities of Port Harcourt, Uyo, and Aba, facilitating the movement of goods and services throughout the region. 

8. Hydroelectric Power Project: Nigeria

Nigeria is building a mega hydropower dam in order to increase its energy production. The Mambila Hydroelectric Power Project, which has been planned for more than three decades, is one of Africa's largest construction projects.

The Mambila Hydroelectric Power Project, which China's Sinohydro Corp is undertaking at a cost of US$5.8 billion, will be linked to three dams across the Donga River in Taraba State, Nigeria. The facility's total installed capacity will be 3,050MW of electricity. In May 2020, ConstructAfrica reported that settlement had been reached on an arbitration case that was delaying the project.

9. The Grand Dam: Ethiopia

The Grand Ethiopian Renaissance Dam, formerly known as the Millennium Dam, is a gravity dam being built on Ethiopia's Blue Nile River in Benishangul-Gumuz.

Work on the 6,000 MW dam began in 2011 and is now 70% complete, falling well short of the July 2017 completion date. Once completed, the Grand Ethiopian Renaissance Dam will be Africa's largest hydroelectric power plant and the world's seventh largest.

Comments

Popular post

What is Slump Test of Concrete-Cone Test Procedure | Workability of Concrete

Slump Test of Concrete-Cone Test Procedure | Workability of Concrete Slump test procedure is to determine the workability of concrete. One of the major problems that you had faced in your field work is concrete compaction during mixing.After mix design, you may have doubt, is this design will be ok? Yes, your design willl be ok in terms of strenght point of view of concrete.But the main problem arises when the mixing of fresh concrete, the compaction of fresh concrete will be very tough.In this situation, you can add some plasticizers without affecting your water-cement ratio or cement-aggregate ratio. Before adding plasticizers or superplasticizers to your fresh concrete, you need to check the workability of your concrete.The slump test is used for checking the workability of concrete.Let us check how can we do slump test of fresh concrete. Apparatus used for cone test procedure 1)Measuring scale 2)Tamping rod 3)Base plate 4)Nonporous base plate 5)Mould for slump test. ...

WHAT ARE THE DESIGN PROCEDURES FOR A BUILDING FOUNDATION?

  DESIGN PROCEDURES FOR A BUILDING FOUNDATION 1. DECIDE THE LOCATION OF COLUMNS & FOUNDATION AND TYPE OF LOADS ACTING ON THEM.(E.X DEAL LOAD,  LIVE LOAD OR WIND LOAD) 2. ESTIMATE ALLOWABLE BEARING PRESSURE OF SOIL USING GROUND INVESTIGATION REPORT. 3. DECIDE DEPTH OF FOUNDATION 4. CALCULATE FOUNDATION AREA 5. DETERMINE VARIATION IN VERTICAL STRESSES 6. CALCULATE SETTLEMENT 7. COST CONTROL 8. CONSIDER TIME 9. VARIATION IN GROUND CONDITION 1. DECIDE THE LOCATION OF COLUMNS & FOUNDATION AND TYPE OF LOADS ACTING ON THEM.(E.X DEAL LOAD,  LIVE LOAD OR WIND LOAD) On the building plan, the position of columns and load bearing walls should be marked, and any other induced loading and bending moments. The loads should be classified into dead, imposed and wind loading, giving the appropriate partial safety factors for these loads. 2. ESTIMATE ALLOWABLE BEARING PRESSURE OF SOIL USING GROUND INVESTIGATION REPORT. From a study of the site ground investigation (if available), th...

What’s the difference between m20 and c20 grade concrete?

 A concrete of Grade C20 means that the concrete will have a compression resistance of 20 N/mm² per square millimeter in 28 days. Proportion for grade C20. C20 is 1:2:4 (1 part cement, 2 parts fine aggregate, and 4 parts coarse aggregate.) where as C20 symbolizes a Cylindrical sample in which cement, fine aggregates, coarse aggregates are mixed in such a ratio that its characteristic compressive strength is 20 N/mm² after 28 days of curing. Fig:- Concrete specimen for testing Generally Strength of Cylinder sample= 0.8 x Strength of Cube. example:- M20 is equivalent to C25 M20 means the grade of concrete is defined as the minimum strength of concrete after 28 days. For the M20 Grade of concrete, The letter ‘M’ refers to the mix, and 20 represents the characteristic strength of concrete in MPa or N/mm². The specified characteristic strength of concrete is determined for 150mm size cube at 28 days. The Characteristic Compressive strength of concrete is defined as the strength of conc...

Different methods of road construction in civil engineering

Different methods of road construction in civil engineering 1) Concrete: It is a common option for road construction purposes as they are a solid material and can be used for building walls and local roads. This method is considerably less prone to wear and tear defects like rutting, cracking, stripping loss of texture, and potholes. This is the main reason for its wide usage. 2) Asphalt: This method of construction replacing concrete method in these days. They are very durable, water-resistant and can go more longer then the concrete. The major advantage of asphalt over concrete is its price. Concrete is very expensive as compared to asphalt. Moreover, asphalt includes low noise during pavement and it is easy to handle it for repairing and maintenance. That is why it is widely accepted and used by the people for the purpose of pavement surfacing. 3) Composite: This method is widely used for the maintenance, recycling, and rehabilitation of the roads. The composite m...

Design Requirement of reinforced Concentrate slab

Table  Content 1 Effective span for concentrate slab design 2 Limiting stiffness 3 Minimum reinforcement 4 Maximum diameter of bar 5 Distribution reinforcement concentrate for slab design 6 Cover to reinforcement Let discuss briefly '''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''' 1. Effective Span for concrete slab design For simply supported slab Minimum of clear span plus effective depth of slab Center to center...

#4 Basic Factors Why Concentrate Cracks?

  WHAT IS CONCRETE : Concrete is a building material which made from mixture of cement , sand ,crush or gravel and water. and we poured this mixture in the form work which can give us the different shapes of element like stone which is too mush strong. WHY CONCRETE CRACKS : 1: Excess of water in concrete 2: Improper Compaction of concrete 3: Rapid drying of concrete 4: Temperature Variation 1: EXCESS OF WATER IN CONCRETE Concrete does not required much water to get maximum strength . we required limit water in concrete to achieve the maximum strength of concrete . when we increase the water in concrete so it can lose the strength , so therefore concrete can crack. water is just reducing in concrete to make workabality of concrete . so increasing of water can reduce the strength of concrete. 2: IMPROPER COMPACTION OF CONCRETE before placing concrete we have to proper compact the soil. and after that when we placed concrete so concrete should be compacted properly . when the con...

What Is Splicing of Reinforcement Bars?,Rebar Formula and Brief Example

 What Is Splicing of Reinforcement Bars? 🏷Splicing of reinforcement bars, commonly known as rebars, refers to the process of connecting two or more rebars in a reinforced concrete structure to ensure a continuous and load-resistant structure. 🚧It is a critical practice in construction to transfer the stresses from one bar to another effectively, maintaining structural integrity. 💫Methods of Splicing Reinforcement Bars There are three primary methods of splicing reinforcement bars: ❇️1. Lap Splice A lap splice is the most widely used method in reinforced concrete structures. In this technique, two rebars are overlapped and tied together using binding wires. The overlap length, also known as the lap length, is crucial for ensuring the splice’s strength. ⏺It is determined based on factors such as: • The diameter of the rebars. • The grade of concrete. • The specific application of the structure. ▶️The lap splice is easy to implement and cost-effective but may require additional con...